---------------------------------------------------------------
An interesting write up in DETAIL Magazine :
http://www.detail.de/artikel_photovoltaics-membrane-structures-jan-cremers_23673_En.htm
I wonder if this might begin to be incorporated into fashion now that they have the technology for malleable pv…
Gives a whole new meaning to “sun dress!”
Research + Technology
Integration of Photovoltaics in Membrane Structures
Membrane materials offer a broad and attractive range of possibilities for the creation of wide-span lightweight building skins with a high level of light transmission. The many different kinds of buildings constructed with high-performance membranes and thin-sheet or film-like materials confirms the enormous potential of these high-tech substances, which in their original built form – i.e. the tent – are among the oldest known to man.
PV Flexibles on PTFE membranesAlthough suspended building elements are ideally suited for large-area structures like stadium roofs and airports, there was hitherto no way of incorporating photovoltaics in them. With its PV Flexibles, SolarNext AG has now developed a form of photovoltaic technology that enables solar cells to be integrated directly into membrane materials.
This technology is based on extremely flexible, amorphous thin-film solar cells embedded in ETFE laminates. Durable building materials like ETFE film and PTFE-coated glass-fibre fabric from the fluoropolymer group are a well-tried solution in everyday practice. They are more durable than PVC membranes; they are resistant to UV-radiation; and their “self-cleansing” surfaces ensure good resistance to soiling.
PV Flexibles can, for example, be used for single-layer roofs and facades without an additional supporting structure. They can also be substituted for the upper layer of pneumatically supported cushions. Used on situations such as these, photovoltaic elements serve not only to generate electricity; they can also provide shade, which may often be an essential requirement.
Anticlastic shape of an integrated photovoltaic- PTFE-membrane structure with applied laminates
Amorphous silicon thin-film cells (a-Si) laminated between two layers of ETFE foilIn this way, insolation within the building in summer can be minimized, thereby reducing the necessary cooling loads and energy consumption. This synergetic effect is especially important, since it helps to improve the economics of the integrated photovoltaic installation.
The development of the thin-film technology used in this context took place at the University of Neuchâtel in Switzerland. In the meantime, it has undergone further refinement by the established Swiss company VHF Technologies, which also manufactures the resultant product. In a continuous (roll-to-roll) production process, the photovoltaic cells are applied to the polymer bearing material in a sequence of layers, whereby the solar cells ultimately have a total thickness of only about 1 µm.
The use of economic polymers as a substrate results in a very high deposition speed in comparison to that of alternative bearing materials such as glass or metal foil. This, in turn, results in moderate substrate temperatures. Otherwise, a thermally induced distortion of the substrate material would inevitably occur, which would present a further obstacle.
According to a study carried out by the Q-Cells company, the potential of this technology in terms of cost savings is superior to that of any other technique. In 2010, the overall costs could be as much as 70 per cent lower than those of comparable modern systems.
Photovoltaic rolls manufactured in this way are cut to length, aligned and joined to form laminates that meet the specific requirements of each project. The photovoltaic membrane is then bedded between two ETFE layers of different thicknesses. This process of lamination ensures that the photovoltaic cells are effectively protected against loads and stresses, as well as against moisture and weathering.
At present, the size of the modules is still limited by the dimensions of the available laminating equipment (approxately 3 m ≈ 1.5 m). Depending on whether they are used in roofs or facades, in a single-layer form of construction or as part of a multilayer membrane cushion, the individual laminae may have to be joined to form larger areas.
To create the relevant three-dimensional form, the edges must be fixed together after cutting, using a special welding process. Only when this has been done can the PV Flexibles be inte-
grated in large-area pneumatic structures.
When the photovoltaic elements are used as an intermediate layer or inside a cushion, they are, of course, optimally protected. In such cases, however, the light-refracting effect of the upper film layer and the thermal gains that occur in the heat-absorbing middle layer would result in a diminution of the energy yield. For that reason, it is clearly preferable to integrate the photovoltaics in the outer layer of the cushion.
Photovoltaic cells integrated in top layer of pneumatic membrane structure
Flexible photovoltaic construction integrated in a large membrane structure (photomontage of Gottlieb Daimler Stadium, Stuttgart)Estimating the yield
Estimating the yield from a photovoltaic system that is incorporated in a membrane structure is a far more complex process than that for conventional photovoltaic modules. The reasons for this are as follows:
• As the product of quite different architectural designs, the geometry of roof and facade structures will obviously vary from project to project and necessitate different layouts for the integral photovoltaic system in each case. In other words, a standard situation that would allow the development of a more or less uniform product scarcely exists.
• The orientation of the individual photovoltaic elements in relation to the sun can vary within a single project. The process of determining the form of the films or membranes – the outcome of a building’s geometry, the supporting structure and the loads to be borne – will also be decisive for the geometry of the photovoltaic system.
• Generally speaking, the surfaces should be curved in at least one direction – better still in two (anticlastic) – otherwise they will not be structurally stable.
• The complex, three-dimensional forms that occur make it more difficult to assess possible shading effects.
Prof. Dr.-Ing. Jan Cremers is director of envelope technology at the Solar
Next AG/Hightex Group in Rimsting on Chiemsee, ¬Germany. He also teaches at Stuttgart University of Applied Sciences.
No comments:
Post a Comment